LOCTITE® 406 Instant Adhesive
Known as Loctite 406 Prism Instant Adhesive
Features and Benefits
Available sizes:
Exceptionally low-viscosity instant adhesives forming an ultra-thin adhesive film for the smallest adhesive gaps in seconds (fast-fixturing). Suitable for plastics and elastomeric materials.
LOCTITE® 406 is a low-viscosity instant adhesive designed especially for the fast bonding of plastics and rubbers. It fixes the adhering components in seconds and hardens very quickly, forming an ultra thin bond. Using the primer LOCTITE® SF 770, the assembly of difficult-to-bond materials (PP, PE, PTFE) is possible.
- Rapid bonding of plastic & rubber, including EPDM
- LOCTITE 770 or LOCTITE 7239 primer improves adhesion of difficult-to-bond substrates
- Low viscosity
Documents and Downloads
Safety Data Sheets and RoHs
- Bottle 10.0/case - IDH 135436
- Bottle 10.0/case - IDH 237295
LOCTITE® 406, 20 g Bottle 135436 en-CA
IDH:
135436
EAN:
079340406407
Size Case: Bottle
Quantity: 10.0/case
LOCTITE® 406, 1 lb Bottle 237295 en-CA
IDH:
237295
EAN:
079340406612
Size Case: Bottle
Quantity: 10.0/case
No documents found
Looking for a TDS or SDS in another language?
Technical Information
| Application method | Dispense system, Manual |
| Applications | Bonding elastomerics, Bonding plastic |
| Color | Clear |
| Cure type | Moisture cure |
| Fixture time, Steel | 30.0 sec. |
| Gap fill | 0.12 mm |
| Key characteristics | Fixture: fast fixture, Viscosity: low viscosity |
| Operating temperature | -40.0 - 120.0 °C (40.0 - 250.0 °F ) |
| Physical form | Liquid |
| Recommended for use with | Elastomer, Plastic, Rubber |
| Shear strength, Mild Steel (grit blasted) | 15.5 N/mm² (2250.0 psi ) |
| Resin | |
| Viscosity, Resin | 20.0 mPa·s (cP) |
How to
Step by Step Guide
1. Preparation - Cleaning
It is recommended to use the correct LOCTITE® cleaner for the surface to be bonded (such as LOCTITE® SF 7070) to degrease and clean surfaces prior to applying the adhesive.
2. Preparation - Priming
To improve adhesion on difficult to bond plastic surfaces, apply LOCTITE® SF 770 to the bond area by brushing or dipping. Avoid applying excess primer. Allow the primer to dry.
3. Preparation - Activation
If cure speed is too slow, use appropriate activator LOCTITE® SF 7452 (see cure speed vs activator graph in TDS). Apply activator to one bond surface by spray, brush or dipping (not primed surfaces). Allow the activator to dry.
4. Application
Apply adhesive onto one side/part.
5. Assembly
Assemble parts immediately. The parts should be accurately located as the short fixture time leaves little opportunity for adjustment. Bond should be held or clamped until the adhesive has fixtured. Hint: if necessary, excess product can be cured by activator LOCTITE® SF 7452. Spray or drop activator onto excess product.
Frequently Asked Questions
What does “non-HQ formula” mean?
Which products are food / drinking water approved?
Why does my plastic crack when I use an instant adhesive?
What health and safety (H&S) precautions do I need to take with this product?
Do instant adhesives need to be refrigerated?
LOCTITE® 406
Exceptionally low-viscosity instant adhesives forming an ultra-thin adhesive film for the smallest adhesive gaps in seconds (fast-fixturing). Suitable for plastics and elastomeric materials.