Bonding applications in the automotive industry have increased significantly during recent years. Learn everything you need to know about roof repair in special laser brazed roofs, applying OEM-approved repair methods.

Get the Materials

In our instruction we show bonding of laser brazed roofs with TEROSON® EP 5065 structural bonder. There are various frame designs and repair methods for roof replacement. Here we only show the repair of the frame design shown above. Make sure to always follow the manufacturer's instructions.


All repair and maintenance tasks shown should be done by professionals only. Please do not try this at home or if not qualified by professional education. Always follow car manufacturer's instructions.
Limitation of liability

STEP 1

Surface Preparation

Grind bondlines to bare metal. Clean and pre-treat the bonding surface with TEROSON® VR 10 using a lint-free cloth. Apply masking tape on the side rail and new roof.

STEP 2

Check new roof

Place the new roof in the cleaned body frame to make sure that it fits.

STEP 3

Mounting Aid I

If you work on bare metal, apply TEROSON® BOND All-in-one Primer for surface preparation for the windscreen adhesive dam / mounting aid.

STEP 4

Preparation of the cartridge

Open TEROSON® EP 5065 cartridge and squeeze out small amount of material until both adhesive components run equally. Clean tip. Apply the mixing nozzle and discard the first 5 cm of the mixed adhesive.

STEP 5

Corrosion Protection

Apply adhesive to the new roof and the body frame. Spread adhesive with a spreader or brush. All bare metal areas should be covered with adhesive (roof and car body frame) for corrosion protection.

STEP 6

Anti flutter application 

Apply TEROSON® MS 222 to roof bows for anti flutter. Mount new roof within processing time of approx. 30 min. Alternatively, apply TEROSON® PU 9161 AF after roof mounting. Neither product causes read-throughs. 

STEP 7

Mounting Aid II

Apply a bead of TEROSON® BOND 60 on the primed surface as a mounting aid parallel to the flange (at a distance of approx. 5 to 8 mm). Consider the processing time.

STEP 8

Adhesive Application

Apply a bead of TEROSON® EP 5065 for bonding. Either to the new roof or to the body frame.

STEP 9

Assembly

Fit the new roof. If spotwelding is required, this work has to be done within 60 min. after product application. 

STEP 10

Post-assembly

Form adhesive and remove excess product with TEROSON® VR 10. Then remove masking tape.


STEP 11

Curing

Cure product at 23°C room temperature for 48 hours. Curing can be accelerated by heat with infrared (30 min. at 80°C object temperature) or heating pads.

Frequently Asked Questions

ANSWERS TO YOUR MOST COMMON QUESTIONS

Limitation of Liability

The information provided herein, especially recommendations for the usage and the application of our products, is based upon our knowledge and experience. Due to different materials used as well as to varying working conditions beyond our control we strictly recommend to carry out intensive trials to test the suitability of our products with regard to the required processes and applications. We do not accept any liability with regard to the above information or with regard to any written or verbal recommendation, except if otherwise explicitly agreed and except in relation to death or personal injury caused by Henkel´s gross negligence or intention and any liability under any applicable mandatory product liability law. Please note that the information provided by us may not be current, complete and correct. It is not intended to serve as legal advice. Each user is solely responsible for assessing and ensuring compliance with any applicable law. The information is protected by copyright. In particular, any reproductions, adaptations, translations, storage and processing in other media, including storage or processing by electronic means, enjoy copyright protection. Any exploitation in whole or in part thereof shall require the prior written consent of Henkel Polska sp. z o.o. Except as otherwise noted, all marks used in this sell sheet are trademarks and/or registered trademarks of Henkel and/or its affiliates.